Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2154

Страница: 2154 / 2589

DTC B2702 [POWER LIFTGATE (PLG) SYSTEM]

DTC B2702 - DETECTION CONDITION POSSIBLE CAUSE CHART

DIAGNOSTIC PROCEDURE

DTC B2702 - DIAGNOSTIC PROCEDURE

Is the wiring harness normal?

VERIFY CORRECTION COMPLETED

Reconnect the disconnected connector.

Clear the DTC.

Is DTC B2701 stored after

5 min or

more

have elapsed?

Yes

Replace the PLG control module.

(See

POWER LIFTGATE (PLG)

CONTROL MODULE

REMOVAL/INSTALLATION

DTC troubleshooting completed.

DTC B2702

PLG touch sensor (RH) circuit malfunction

DETECTION

CONDITION

A short circuit to ground in the PLG touch sensor (RH) continues for 5 min or more.

POSSIBLE CAUSE

Short to GND in wiring harness between PLG control module terminal 3A and

PLG touch sensor (RH) terminal B

PLG touch sensor (RH) malfunction

Obstructions in the detection part

PLG control module malfunction

STEP

INSPECTION

ACTION

INSPECT PLG TOUCH SENSOR (RH)

Yes Go to the next step.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES On-Board Diagnostic (Power Liftgate (PLG) System) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:46:08 AM

Page 33

«
...
2152
2153
2154
2155
2156
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды