Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2382

Страница: 2382 / 2589

1. Adjust the door glass position as shown in the figure.
2. Disconnect the negative battery cable.
3. Remove the inner garnish. (See

INNER GARNISH REMOVAL/INSTALLATION

4. Remove the front door trim. (See

FRONT DOOR TRIM REMOVAL/INSTALLATION

5. Remove the front door speaker. (See

FRONT DOOR SPEAKER REMOVAL/INSTALLATION

Fig. 2: Identifying Front Door Glass Position

Courtesy of MAZDA MOTORS CORP.

6. Remove the hole cover.
7. Remove the bolts.

Fig. 3: View Of Hole Cover & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

Lift the front door glass up and remove it in the direction of the arrow.

Install in the reverse order of removal.

NOTE:

When installing the front door glass, align the glass edge with the

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Glass/Windows/Mirrors - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:36:16 AM

Page 3

«
...
2380
2381
2382
2383
2384
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды