Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1649 | Manualshive

Страница: 1649 / 2589

background image

Fig. 9: Identifying SST Lever

Courtesy of MAZDA MOTORS CORP.

Using M-MDS

1. Connect the negative battery cable. (See

BATTERY REMOVAL/INSTALLATION [MZI-3.7]

.)

2. Connect the M-MDS to the DLC-2.
3. Using the simulation function "FP", start the fuel pump.

Fig. 10: Connecting M-MDS To DLC-2

Courtesy of MAZDA MOTORS CORP.

Without using M-MDS

1. Remove the fuel pump relay.

2. Using a jumper wire, short fuel pump relay terminals C and D in the main fuse block.
3. Connect the negative battery cable and operate the fuel pump.

CAUTION:

z

Short the specified terminals because shorting the wrong

terminal of the main fuse block may cause malfunctions.

2008 Mazda CX-9 Grand Touring

2008 ENGINE Fuel System (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:00:01 AM

Page 8

© 2005 Mitchell Repair Information Company, LLC.

«
...
1647
1648
1649
1650
1651
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: DAVIS Страницы: 32

BLADE-AL(TB)-TL2

Бренд: iDataLink Страницы: 9

Бренд: Magneti Marelli Страницы: 2

Бренд: hc-cargo Страницы: 60

Бренд: MASCOT Страницы: 12

Бренд: Motoalliance Страницы: 8

Бренд: ULTIMATE SPEED Страницы: 21

TRI-FOLD PG9300RF

Бренд: Pet Gear Страницы: 4

Бренд: Weltmann KFZ-Teile Страницы: 12

Бренд: Thule Страницы: 4

THERAPEDIC 2000

Бренд: Columbia Страницы: 14

Бренд: Dakota Digital Страницы: 20

Бренд: Roadmaster Страницы: 4

Бренд: Menabo Страницы: 8

Бренд: Crux Страницы: 10

Бренд: GEMINI TECHNOLOGY Страницы: 9

Бренд: Truma Страницы: 84

Бренд: Honda Страницы: 358

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды