Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2417 | Manualshive

Страница: 2417 / 2589

background image

QUARTER WINDOW GLASS INSTALLATION

1. Remove sealant along the perimeter of the glass using a razor or scraper, (when reusing the glass)
2. Clean and degrease the ceramic part along the perimeter of the glass.
3. Inspect the glass for cracks. If it is cracked, chamfer it using sandpaper.
4. If the glass is reused, attach the pins and fastener to the glass as shown in the figure. Align with the

alignment marks marked before removing the glass.

Fig. 53: Identifying Quarter Window Glass And Pin
Courtesy of MAZDA MOTORS CORP.

WARNING:

z

Using a razor with bare hands can cause injury. Always wear gloves
when using a razor.

CAUTION:

z

If a door is opened or closed when all the window glass is closed, the

resulting change in air pressure could cause the sealant to crack
preventing the proper installation of the glass. Keep the door glass

open until the quarter window glass installation is completed.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Glass/Windows/Mirrors - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:36:16 AM

Page 38

© 2005 Mitchell Repair Information Company, LLC.

«
...
2415
2416
2417
2418
2419
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: Tessera4x4 Страницы: 20

inView 360 Fusion

Бренд: Safe Fleet Страницы: 27

ROADSIDE ASSISTANCE

Бренд: Seat Страницы: 44

Бренд: Beper Страницы: 52

Бренд: OHIOSTEEL Страницы: 2

Бренд: Thule Страницы: 4

Ridesmart KMA-610

Бренд: KlipXtreme Страницы: 12

Бренд: Ford Страницы: 4378

Бренд: Toyota Страницы: 549

Бренд: Axxess Страницы: 8

Бренд: Acura Страницы: 347

Бренд: Volkswagen Zubehör Страницы: 133

Бренд: Discount Car Stereo Страницы: 11

Бренд: Westin Страницы: 2

Бренд: Prorack Страницы: 15

Бренд: Blackhawk Automotive Страницы: 8

Бренд: AutoMaxi Страницы: 2

Бренд: Cadillac Страницы: 362

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды