Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 289

Страница: 289 / 2589

Fig. 227: Identifying Thrust Bearing And Bearing Races

Courtesy of MAZDA MOTORS CORP.

13. Apply ATF to each gear and the bushing, and then install the rear planetary gear component to the

transaxle case.

14. Apply ATF to the sliding surface of the one-way clutch.

Fig. 228: Identifying Rear Planetary Gear Component

Courtesy of MAZDA MOTORS CORP.

15. Install the one-way clutch to the transaxle case.

NOTE:

For easy installation, while turning the rear planetary gear
component, install it.

2008 Mazda CX-9 Grand Touring

2005-08 TRANSMISSION Automatic Transaxle Overhaul (AW6A-EL) - CX-7, CX-9 & Mazda 6

Microsoft

Sunday, November 15, 2009 10:28:17 AM

Page 126

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды