Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1877 | Manualshive

Страница: 1877 / 2589

background image

REMOVAL/INSTALLATION

.)

2. Side wall (See

SIDE WALL REMOVAL/INSTALLATION

.)

3. Console panel (LH) (See

CONSOLE PANEL REMOVAL/INSTALLATION

.)

4. Hood release lever (See

HOOD LATCH AND RELEASE LEVER

REMOVAL/INSTALLATION

.)

3. Remove the screw.
4. Detach clips A and hook B by pulling them in the direction of the arrow.
5. Remove the hook B.
6. Disconnect the head light leveling switch connector and TCS OFF switch connector.
7. Disconnect the BSM OFF switch connector. (Vehicles with BSM)
8. Disconnect the PLG switch connector. (Vehicles with PLG)
9. Disconnect the cabin temperature sensor connector and air hose.

10. Remove the lower panel.
11. Install in the reverse order of removal.

Fig. 15: Identifying Lower Panel Components

Courtesy of MAZDA MOTORS CORP.

SIDE PANEL REMOVAL/INSTALLATION

1. Remove the glove compartment service hole cover. (See

AIR FILTER

REMOVAL/INSTALLATION

.)

2. Insert fingers into the glove compartment service hole and detach the tabs A.
3. Remove the side panel in the direction of the arrow.
4. Install in the reverse order of removal.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Interior Trim - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:43:26 AM

Page 13

© 2005 Mitchell Repair Information Company, LLC.

«
...
1875
1876
1877
1878
1879
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: AA Products Страницы: 6

Бренд: Camoplast Страницы: 60

Бренд: RAM Commercial Страницы: 12

Бренд: Carax Страницы: 2

Brute Strength 12057.0271

Бренд: Quadratec Страницы: 6

Бренд: Compass Страницы: 16

Бренд: Toyota Страницы: 52

Бренд: PEUGEOT Страницы: 249

Бренд: GMC Страницы: 20

Бренд: Würth Страницы: 36

Бренд: Hummer Страницы: 502

Бренд: Vauxhall Страницы: 259

Бренд: Opel Страницы: 32

Бренд: Draw tite Страницы: 4

Бренд: EFILive Страницы: 25

Бренд: GYS Страницы: 32

Бренд: Prime Design Страницы: 8

Бренд: Aries Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды