Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 176

Страница: 176 / 2589

Fig. 18: Fixing Coupler Component With Tape To Transaxle Case

Courtesy of MAZDA MOTORS CORP.

16. Remove the VSS connector and input/turbine speed sensor connector from the solenoid clamp.

Fig. 19: Identifying VSS Connector And Input/Turbine Speed Sensor Connector

Courtesy of MAZDA MOTORS CORP.

17. Secure the VSS wiring harness and input/turbine speed sensor wiring harness with tape to the transaxle

case as shown in the figure.

NOTE:

Be sure to secure the VSS and input/turbine speed sensor with tape
so that they do not interfere with the control valve body component.

2008 Mazda CX-9 Grand Touring

2005-08 TRANSMISSION Automatic Transaxle Overhaul (AW6A-EL) - CX-7, CX-9 & Mazda 6

Microsoft

Sunday, November 15, 2009 10:28:15 AM

Page 13

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды