Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 834

Страница: 834 / 2589

[MZI-3.7]

If the monitor item status/specification (reference) is not within the specification, even though the

resistance is within the specification, perform the "Circuit Open/Short Inspection".

IAT sensor resistance

IAT SENSOR RESISTANCE SPECIFICATION CHART

IAT sensor characteristics graph (reference)

Fig. 13: Temperature Vs Resistance Graph

Courtesy of MAZDA MOTORS CORP.

CIRCUIT OPEN/SHORT INSPECTION

IAT (°C {°F}) Resistance (kilohm)

10(50}

Approx. 58.75

20 {68}

Approx. 37.30

30 {86}

Approx. 24.27

60 {140}

Approx. 7.70

2008 Mazda CX-9 Grand Touring

2008 ENGINE Control System (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:07:19 AM

Page 16

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды