Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1564 | Manualshive

Страница: 1564 / 2589

background image

Fig. 25: Identifying Front Side Garnish With Clips

Courtesy of MAZDA MOTORS CORP.

REAR

1. Pull the side garnish and remove clip A from the vehicle body.
2. Slide the side garnish to the vehicle rear and remove clips B and C from the side garnish.
3. Remove the side garnish.
4. Remove clips B and C from the body, then install it to the side garnish.

Fig. 26: Identifying Rear Side Garnish With Clips

Courtesy of MAZDA MOTORS CORP.

SIDE GARNISH INSTALLATION

FRONT

1. Install clips A and then B to the vehicle from the front side.

2008 Mazda CX-9 Grand Touring

2008 ACCESSORIES & BODY, CAB Exterior Trim - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:44:03 AM

Page 19

© 2005 Mitchell Repair Information Company, LLC.

«
...
1562
1563
1564
1565
1566
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: FABBRI PORTATUTTO Страницы: 2

Бренд: Mercedes-Benz Страницы: 30

Бренд: FORM FIT Страницы: 2

Бренд: CITROEN Страницы: 52

FIX&GO automatic

Бренд: Alfa Romeo Страницы: 40

2011 Civic Sedan

Бренд: Honda Страницы: 5

990E0-54P56-000

Бренд: Suzuki Страницы: 12

Бренд: AA Products Страницы: 6

Ford 4” UNI-CAM

Бренд: Nav TV Страницы: 6

2007 9-3 Remote Starter

Бренд: Saab Страницы: 304

Бренд: MULTILIFT Страницы: 62

Бренд: APS Страницы: 3

Бренд: Edelbrock Страницы: 4

Бренд: Mitsubishi Страницы: 490

Бренд: Audi Страницы: 9

Бренд: Hyundai Страницы: 32

Бренд: Harbor Freight Tools Страницы: 8

MKZ HYBRID 2016

Бренд: Lincoln Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды