Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1962

Страница: 1962 / 2589

Fig. 69: Terminals Continuity Chart

Courtesy of MAZDA MOTORS CORP.

Fig. 70: Checking Continuity Between Cargo Compartment Light Terminals

Courtesy of MAZDA MOTORS CORP.

COURTESY LIGHT BULB REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.
2. Remove in the order indicated in the table.

Fig. 71: Identifying Courtesy Light Bulb & Lens

Courtesy of MAZDA MOTORS CORP.

3. Install in the reverse order of removal.

LENS REMOVAL NOTE

1. Insert a tape-wrapped flathead screwdriver into the service hole and pry with the screwdriver in the

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Lighting Systems - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:39:06 AM

Page 46

«
...
1960
1961
1962
1963
1964
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды