Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 39

Страница: 39 / 2589

Turn the ignition switch to the LOCK position.

Disconnect the negative battery cable and wait

for

1 min or more.

Disconnect the crash zone sensor connector.
(See

CRASH ZONE SENSOR

REMOVAL/INSTALLATION

Is there any malfunction of the crash zone
sensor connector?

WARNING:

Handling the air bag system components

improperly can accidentally deploy the air
bag modules and pre-tensioner seat belts,

which may seriously injure you. Read the

service warnings and cautions before
handling the air bag system components.

(See AIR BAG SYSTEM SERVICE

WARNINGS .)

(See AIR BAG SYSTEM SERVICE

CAUTIONS .)

Yes Replace the air bag wiring harness.

Go to the next step.

INSPECT WIRING HARNESS BETWEEN

CRASH ZONE SENSOR AND SAS CONTROL
MODULE

Turn the ignition switch to the LOCK position.

Disconnect the negative battery cable and wait

for

1 min or more.

Remove the column cover. (See

COLUMN

COVER REMOVAL/INSTALLATION

Disconnect the clock spring connector. (See

COMBINATION SWITCH

REMOVAL/INSTALLATION

Remove the glove compartment. (See

GLOVE

COMPARTMENT

REMOVAL/INSTALLATION

Disconnect the passenger-side air bag module
connector. (See

PASSENGER-SIDE AIR

BAG MODULE
REMOVAL/INSTALLATION

Disconnect the driver and passenger-side front

seat connectors. (See

FRONT SEAT

REMOVAL/INSTALLATION

Yes

Replace the crash zone sensor, then go
to the next step.

(See

CRASH ZONE SENSOR

REMOVAL/INSTALLATION

2008 Mazda CX-9 Grand Touring

2008 RESTRAINTS On-Board Diagnostic (Restraints) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:18:46 AM

Page 39

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды