Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2199

Страница: 2199 / 2589

Fig. 4: Ignition Switch Terminals Continuity Chart

Courtesy of MAZDA MOTORS CORP.

Fig. 5: Identifying Ignition Switch Terminals

Courtesy of MAZDA MOTORS CORP.

KEY REMINDER SWITCH REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.
2. Remove the column cover. (See

COLUMN COVER REMOVAL/INSTALLATION

3. Disconnect the key reminder switch connector.
4. Remove the key reminder switch.
5. Install in the reverse order of removal.

2008 Mazda CX-9 Grand Touring

2008 ACCESSORIES & BODY, CAB Power Systems - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:41:28 AM

Page 3

«
...
2197
2198
2199
2200
2201
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды