Toro Security Cage Kit Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 8

Toro Security Cage Kit Скачать руководство пользователя страница 1

Form No. 3419-943 Rev B

Security Cage Kit

Groundsmaster

®

4500, 4700, or Reelmaster

®

7000 Series Traction

Unit with 2 Post ROPS Extension

Model No. 31606

Installation Instructions

This kit fits 2-Post ROPS Extension Kit Model 31351 only.

Note:

Determine the left and right sides of the machine from the normal operating position.

Note:

Have an assistant help you to install this kit.

1

Preparing the Machine

No Parts Required

Procedure

1.

Park the machine on a level surface.

2.

Lower the cutting units.

3.

Engage the parking brake.

4.

Shut off the engine and remove the key.

5.

If there are lights on the roll bar, remove the lights and mounting hardware from the roll bar.

Retain the lights and the mounting hardware

6.

If a 2 Post ROPS extension was installed on the machine, remove the side panels that are used to
mount the ROPS post lights (

).

Note:

Retain the ROPS clamps and corresponding hardware.

7.

Position the control console to the furthest inward position.

© 2019—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420

Register at www.Toro.com.

Original Instructions (EN)

Printed in the USA

All Rights Reserved

*3419-943* B

1
2
3
...
»

Содержание Security Cage Kit









Отзывы:

Нет отзывов