Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1892

Страница: 1892 / 2589

2. Pull the A-pillar trim shown in the figure in the direction of the arrow, raise clip B from its grommet

together with the A-pillar trim, and remove clips A at the same time.

Fig. 41: Identifying A-Pillar Trim & Clips

Courtesy of MAZDA MOTORS CORP.

3. Slide the A-pillar trim in the direction of the arrow shown in the figure and remove the A-pillar trim from

clip B.

Fig. 42: Sliding A-Pillar Trim

Courtesy of MAZDA MOTORS CORP.

4. Rotate and pull clip B in the direction of the arrow shown in the figure until it is no longer loose, and

feels tight.

5. Pull clip B and remove it from the grommet.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Interior Trim - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:43:26 AM

Page 28

«
...
1890
1891
1892
1893
1894
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды