Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 634

Страница: 634 / 2589

3. Remove the clips securing the wiring harness shown in the figure and set the wiring harness out of the

way.

Fig. 8: Identifying Rear Door Module And Clip

Courtesy of MAZDA MOTORS CORP.

4. Remove screws and fastener.
5. Remove the rear door module.
6. Install in the reverse order of removal.

Fig. 9: Identifying Rear Door Module With Screws And Fastener

Courtesy of MAZDA MOTORS CORP.

LIFTGATE REMOVAL/INSTALLATION

WARNING:

When removing the stay damper, serious injury may occur if the stay

damper is removed without supporting the liftgate. Always perform
the procedure with at least another person.

CAUTION:

If replacing the rear window glass, leave the power liftgate (PLG)

unoperated for two days after the rear Window glass installation. If
the power liftgate (PLG) is operated automatically with the sealant

not hardened after the rear window glass installation, the liftgate may

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Doors and Liftgate - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:45:23 AM

Page 8

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды