Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2093

Страница: 2093 / 2589

REMOVAL/INSTALLATION

Inspect the connection of the driver-side

front door speaker connector (2-pin).

Is the connector securely connected?

Securely connect the driver-side front door

speaker connector.

Disconnect the driver-side front door
speaker connector (2-pin).

Inspect both the driver-side front door

speaker and wiring harness-side
connector for poor connection (such as

damaged/pulled-out pins, corrosion).

Are all the pins normal?

Yes Go to the next step.

If the driver-side front door speaker side

connector is wrong:

Replace the driver-side front door

speaker. (See

FRONT DOOR

SPEAKER

REMOVAL/INSTALLATION

If the wiring harness-side connector is

wrong:

Repair or replace the pins and/or the

connector.

Inspect for continuity between audio
amplifier and the driver-side front door

speaker.

Is there continuity?

Yes Go to the next step.

Repair or replace the wiring harness.

Inspect the driver-side front door speaker.
(See

FRONT DOOR SPEAKER

INSPECTION

Is it normal?

Yes Go to the next step.

Replace the driver-side front door speaker.

(See

FRONT DOOR SPEAKER

REMOVAL/INSTALLATION

Remove the car-navigation unit. (See

CAR-NAVIGATION UNIT
REMOVAL/INSTALLATION

Inspect the connection of the car-

navigation unit connector (16-pin).

Is the connector securely connected?

Yes Go to the next step.

Securely connect the car-navigation unit

connector.

Disconnect the car-navigation unit

connector (16-pin).

Inspect both the car-navigation unit and

wiring harness-side connector terminal F,
I and K for poor connection (such as

damaged/pulled-out pins, corrosion).

Are all the pins normal?

Yes Go to the next step.

If the car-navigation unit side connector is

wrong:

Replace the car-navigation unit. (See

CAR-NAVIGATION UNIT

REMOVAL/INSTALLATION

If the wiring harness-side connector is

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Symptom Troubleshooting (Car Navigation System) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:40:44 AM

Page 12

«
...
2091
2092
2093
2094
2095
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды