Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2446 | Manualshive

Страница: 2446 / 2589

background image

4. Squeeze the tabs of the windshield washer nozzle.
5. Pull the windshield washer nozzle out to remove it.
6. Install in the reverse order of removal.

Fig. 13: Removing Windshield Washer Nozzle

Courtesy of MAZDA MOTORS CORP.

WINDSHIELD WASHER HOSE REMOVAL/INSTALLATION

1. Remove the splash shield (RH). (See

SPLASH SHIELD REMOVAL/INSTALLATION

.)

2. Disconnect windshield washer hose A from the windshield washer motor.
3. Remove windshield washer hose A from clip A.
4. Disconnect joint pipe A and remove windshield washer hose A.
5. Detach clips B.
6. Disconnect joint pipe A and B and remove windshield washer hose B.
7. Remove the windshield wiper arm and blade. (See

WINDSHIELD WIPER ARM AND BLADE

REMOVAL/INSTALLATION

.)

8. Remove the cowl grille. (See

COWL GRILLE REMOVAL/INSTALLATION

.)

2008 Mazda CX-9 Grand Touring

2008 ACCESSORIES & BODY, CAB Wiper/Washer System - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:35:20 AM

Page 11

© 2005 Mitchell Repair Information Company, LLC.

«
...
2444
2445
2446
2447
2448
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: RAM Страницы: 116

Бренд: Pivot Страницы: 4

Бренд: Daewoo Страницы: 68

Бренд: Hyundai Страницы: 437

Бренд: TrailFX Страницы: 6

Automotive 31006

Бренд: KRAFTWERK Страницы: 2

Бренд: tams elektronik Страницы: 19

PRIME DESIGN HRR-369-E-UM3-96

Бренд: Safe Fleet Страницы: 12

Бренд: Kocchi's Страницы: 4

Бренд: Calix Страницы: 4

Бренд: Rhino-Rack Страницы: 2

Бренд: Metra Electronics Страницы: 12

Бренд: Kleinn Air Horns Страницы: 33

Бренд: Rally Armor Страницы: 4

Prime Design AAL-8003

Бренд: Safe Fleet Страницы: 8

Бренд: Igloo Страницы: 76

Бренд: Mack Страницы: 133

XEV1R22T2 Series

Бренд: hager Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды