Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2432

Страница: 2432 / 2589

Fig. 80: Identifying Rearview Mirror And Rearview Mirror Cover

Courtesy of MAZDA MOTORS CORP.

4. Make a tool as shown in the figure using wire.

5. Insert the tool to the position shown in the figure and push the center part of the spring.

CAUTION:

Using the tool with bare hands can cause injury. Always wear
gloves when using the tool.

To prevent damage to the lens sensor, do not use a screwdriver.

Fig. 81: Identifying Rearview Mirror Removal Tool

Courtesy of MAZDA MOTORS CORP.

CAUTION:

Perform the procedure while being careful not to damage the

lens sensor.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Glass/Windows/Mirrors - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:36:17 AM

Page 53

«
...
2430
2431
2432
2433
2434
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды