Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 82

Страница: 82 / 2589

Turn the ignition switch to the LOCK

position.

Disconnect the negative battery cable and
wait for

1 min or more.

Remove the column cover. (See

COLUMN

COVER REMOVAL/INSTALLATION

Disconnect the clock spring connector. (See

COMBINATION SWITCH

REMOVAL/INSTALLATION

Remove the glove compartment. (See

GLOVE COMPARTMENT

REMOVAL/INSTALLATION

Disconnect the passenger-side air bag

module connector. (See

PASSENGER-

SIDE AIR BAG MODULE

REMOVAL/INSTALLATION

Disconnect the driver and passenger-side
front seat connectors. (See

FRONT SEAT

REMOVAL/INSTALLATION

Disconnect the driver and passenger-side
curtain air bag module connectors. (See

CURTAIN AIR BAG MODULE
REMOVAL/INSTALLATION

Remove the B-pillar lower trim. (See

B-

PILLAR LOWER TRIM
REMOVAL/INSTALLATION

Disconnect the driver and passenger-side

pre-tensioner seat belt connectors. (See

FRONT SEAT BELT

REMOVAL/INSTALLATION

Disconnect the SAS control module
connectors. (See

SAS CONTROL

MODULE
REMOVAL/INSTALLATION

Disconnect the seat track position sensor

system components.

(See AIR BAG SYSTEM SERVICE

WARNINGS .)

(See AIR BAG SYSTEM SERVICE

CAUTIONS .)

Yes

Replace the seat track position sensor,
then go to next step.

Replace wiring harness, then go to next

step.

2008 Mazda CX-9 Grand Touring

2008 RESTRAINTS On-Board Diagnostic (Restraints) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:18:47 AM

Page 82

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды