Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 434 | Manualshive

Страница: 434 / 2589

background image

5. Install the clip as shown in the figure.

Fig. 28: Identifying Clip

Courtesy of MAZDA MOTORS CORP.

6. Install the selector lever to the manual shaft lever so that no load acts on the selector cable.
7. Confirm that the tip of the manual shaft lever projects out of the end of the selector cable.
8. Securely install the selector cable to the selector cable bracket.

Fig. 29: Inspecting Clip Side Of Selector Cable End Facing Up

Courtesy of MAZDA MOTORS CORP.

INTERLOCK CABLE INSTALLATION NOTE

1. Push the interlock cable.

NOTE:

z

Install the selector lever to the manual shaft lever with the clip side of
the selector cable end facing up.

2008 Mazda CX-9 Grand Touring

2008 TRANSMISSION Automatic Transaxle Shift Mechanism - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:30:13 AM

Page 14

© 2005 Mitchell Repair Information Company, LLC.

«
...
432
433
434
435
436
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: LAMBORGHINI Страницы: 48

Бренд: Yakima Страницы: 19

UCI-11C NTV-KIT331

Бренд: Nav TV Страницы: 4

Бренд: STC Страницы: 6

Бренд: Jeep Страницы: 380

Ferrari 360 Map Carbon Light

Бренд: MAcarbon Страницы: 4

Бренд: CALIMA Страницы: 9

Бренд: MULTILIFT Страницы: 62

Бренд: Porsche Страницы: 145

MagicWatch MWE150

Бренд: Waeco Страницы: 176

Бренд: Ecco Страницы: 11

Бренд: Fyndr Страницы: 20

Бренд: Geely Страницы: 188

Бренд: Ford Страницы: 10

Бренд: Craftsman Страницы: 5

Бренд: Craftsman Страницы: 7

Бренд: Craftsman Страницы: 9

Бренд: Craftsman Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды