Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1582

Страница: 1582 / 2589

Fig. 15: Pressing Dust Cover

Courtesy of MAZDA MOTORS CORP.

WHEEL BEARING INSTALLATION NOTE

1. Install the new wheel bearing using the

SSTs.

Substitution SST

49 F027 004

Outer diameter: 78-83 mm {3.1-3.2 in}

49 F027 009

Outer diameter: 77-82 mm {3.1-3.2 in}

Fig. 16: Pressing Wheel Bearing Installation Position

Courtesy of MAZDA MOTORS CORP.

WHEEL HUB INSTALLATION NOTE

1. Install the wheel hub using the

SSTs.

Substitution SST

2008 Mazda CX-9 Grand Touring

2008 DRIVELINE/AXLE Front Axle - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:53:51 AM

Page 9

«
...
1580
1581
1582
1583
1584
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды