Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 424

Страница: 424 / 2589

5. Remove the lock unit from the bracket.

Fig. 6: Identifying Lock Unit And Bracket

Courtesy of MAZDA MOTORS CORP.

6. Verify that the marking on the slider pin is positioned as shown in the figure.

Fig. 7: Inspecting Marking On Slider Pin Is Positioned

Courtesy of MAZDA MOTORS CORP.

7. Push the interlock cable.

Fig. 8: Pushing Interlock Cable

Courtesy of MAZDA MOTORS CORP.

2008 Mazda CX-9 Grand Touring

2008 TRANSMISSION Automatic Transaxle Shift Mechanism - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:30:13 AM

Page 4

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды