Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 706

Страница: 706 / 2589

1. Select "Chassis".
2. Select "ABS/DSC".
3. Select "Sensor Initialization".

When using the PDS (Pocket PC)

1. Select "Module Test".
2. Select "ABS".
3. Select "Datalogger".
4. Select "SSR_INTL".

6. Perform the initialization according to the directions on the screen.

Fig. 14: Connecting M-MDS To DLC-2

Courtesy of MAZDA MOTORS CORP.

DSC/RSC HU/CM INSPECTION

1. Disconnect the DSC/RSC HU/CM connector. (See

DSC/RSC HU/CM

REMOVAL/INSTALLATION

2. Connect the negative battery cable. (See

BATTERY REMOVAL/INSTALLATION [MZI-3.7]

3. Attach the tester lead to the DSC/RSC HU/CM harness side connector, then inspect voltage, continuity or

resistance according to the standard (reference value) on the table.

STANDARD (REFERENCE VALUE)

2008 Mazda CX-9 Grand Touring

2008 BRAKES Dynamic Stability Control/Roll Stability Control - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:40:24 AM

Page 13

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Mazda CX-9 Grand Touring 2008, Руководство пользователя, Страница: 706 / 2589

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы: