Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2102

Страница: 2102 / 2589

Microphone related signal inspection:

1. Press the "Menu" button on the "Diagnosis Check" screen.
2. Select "Navigation Check Menu".
3. Select "Microphone Check".

Fig. 3: Diagnosis Check Screen Display - Microphone Check

Courtesy of MAZDA MOTORS CORP.

MICROPHONE CHECK INSPECTION CHART

4 SPEED

(1)

Indicates the present vehicle speed in kph/mph (maximum of 3 digits).

5 TNS

(1)

Indicates TNS signal status.

ON: Turn TNS ON

OFF: Turn TNS OFF

6 GPS Antenna

(1)

Indicates the connection status of the GPS antenna.

OK: Connected

NCON: Disconnected

7 Traffic System

Indicates RDS-TMC system availability on the vehicle.

TMC: Equipped

NONE: Not equipped

(1)

Used for symptom troubleshooting. (Troubleshooting index No. 5 and No. 8)

No.

Display item

Description

1 PTT switch status

Indicates the status of the VOICE button.

< OK >: Press the button (Keep the state until the screen is

changed.)

< Please Push Switch >: Other than above condition.

Indicates the test results.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Symptom Troubleshooting (Car Navigation System) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:40:44 AM

Page 21

«
...
2100
2101
2102
2103
2104
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды