Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2208 | Manualshive

Страница: 2208 / 2589

background image

1. Remove the presilencer installation nuts. (Middle pipe side) (See

EXHAUST SYSTEM

REMOVAL/INSTALLATION [MZI-3.7]

.)

2. Disconnect the hanger rubber as shown in the figure.
3. Suspend the presilencer using a cable.
4. Remove the presilencer insulator.
5. Remove in the order indicated in the figure.

Fig. 4: Identifying Presilencer Insulator And Presilencer

Courtesy of MAZDA MOTORS CORP.

6. Install in the reverse order of removal.

2008 Mazda CX-9 Grand Touring

2008 DRIVELINE/AXLE Propeller Shaft - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:53:04 AM

Page 3

© 2005 Mitchell Repair Information Company, LLC.

«
...
2206
2207
2208
2209
2210
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: Daihatsu Страницы: 1718

SP200 - QUICKSTART GUIDE 1

Бренд: Jabra Страницы: 2

BT150 - Headset - Over-the-ear

Бренд: Jabra Страницы: 2

Бренд: Westin Страницы: 3

Бренд: Vintage Air Страницы: 28

Бренд: FORM FIT Страницы: 2

Бренд: Yakima Страницы: 21

Бренд: Chevrolet Страницы: 376

Бренд: Mazda Страницы: 15

Бренд: Whispbar Страницы: 15

DAF CHARGEMAX 90

Бренд: Paccar Страницы: 40

Бренд: Metra Electronics Страницы: 5

Бренд: Renkforce Страницы: 4

Бренд: KEKO Страницы: 13

Stealth 4191F Series

Бренд: Road Armor Страницы: 5

Stargazer Spirit XTR Skylight

Бренд: Lippert Страницы: 8

Бренд: Magneti Marelli Страницы: 9

Бренд: Feniex Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды