Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1823

Страница: 1823 / 2589

Connect terminals 1D and 1R of the instrument
cluster.

Go to the next

step.

Except above

Go to the Step 6.

Using the

SST

(Fuel and thermometer checker) or

resistor, input

20 ohms

between instrument cluster

terminals 1D and 1R.

Go to the next
step.

Except above

Go to the Step 6.

Using the

SST

(Fuel and thermometer checker) or

resistor, input

60 ohms

between instrument cluster

terminals 1D and 1R.

Go to the next
step.

Except above

Go to the Step 6.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Instrumentation/Driver Info - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:42:27 AM

Page 13

«
...
1821
1822
1823
1824
1825
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды