manualshive.com logo in svg

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Mazda CX-9 Grand Touring 2008 - роскошный семиместный кроссовер с высоким уровнем комфорта и мощным двигателем. Перед вами отличная возможность скачать бесплатно руководство пользователя для этой модели на manualshive.com. Получите свой экземпляр уже сегодня и ознакомьтесь с функциональностью автомобиля.

Поделиться
Скачать
background image

REAR EVAPORATOR TEMPERATURE SENSOR REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.  
2. Remove the following parts: 

1. Decoration panel (See 

DECORATION PANEL REMOVAL/INSTALLATION

 .)  

2. Front console box mat (See 

FRONT CONSOLE BOX MAT REMOVAL/INSTALLATION

 .)  

3. Indicator panel (See 

INDICATOR PANEL REMOVAL/INSTALLATION

 .)  

4. Front console box (See 

FRONT CONSOLE BOX REMOVAL/INSTALLATION

 .)  

5. Side wall (See 

SIDE WALL REMOVAL/INSTALLATION

 .)  

6. Dashboard under cover (See 

DASHBOARD UNDER COVER REMOVAL/INSTALLATION

.) 

7. Console panel (See 

CONSOLE PANEL REMOVAL/INSTALLATION

 .)  

8. Console cover (See 

CONSOLE COVER REMOVAL/INSTALLATION

 .)  

9. Console (See 

CONSOLE REMOVAL/INSTALLATION

 .)  

3. Disconnect the rear evaporator temperature sensor connector and remove it from the rear A/C unit.  
4. Insert a flathead screwdriver as shown in the figure and remove the clip by prying it off.  
5. Remove the rear evaporator temperature sensor.  
6. Install in the reverse order of removal. 

Fig. 50: Identifying Rear Evaporator Temperature Sensor & Connector

 

Courtesy of MAZDA MOTORS CORP.

 

REAR EVAPORATOR TEMPERATURE SENSOR INSPECTION 

 

2008 Mazda CX-9 Grand Touring 

2008 HVAC Control System (HVAC) - Mazda CX-9

  

Microsoft 

 

Sunday, November 15, 2009 10:12:36 AM

Page 31 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Camcar 2155 Fitting Instructions preview
2155
Бренд: Camcar Страницы: 2
LaserTrack Flare Installation Manual preview
Flare
Бренд: LaserTrack Страницы: 12
iDataLink maestro Rr Install Manual preview
maestro Rr
Бренд: iDataLink Страницы: 106
RAM 2015 1500 User Manual preview
2015 1500
Бренд: RAM Страницы: 292
RAM Trucks 1500 User Manual preview
Trucks 1500
Бренд: RAM Страницы: 116
Yakima K831 Manual preview
K831
Бренд: Yakima Страницы: 8
UGREEN Car Cup Holder Phone Mount Manual preview
Car Cup Holder Phone Mount
Бренд: UGREEN Страницы: 9
Audiovox Code Alarm PROFESSIONAL SERIES CA 5550SST Owner'S Manual preview
Code Alarm PROFESSIONAL SERIES CA 5550SST
Бренд: Audiovox Страницы: 14
Whispbar K678W Fitting Instructions Manual preview
K678W
Бренд: Whispbar Страницы: 14
SCC Quik Grip Installation And Removal Instructions preview
Quik Grip
Бренд: SCC Страницы: 4
C-KO RS-4-18-R-I Fitting Instructions preview
RS-4-18-R-I
Бренд: C-KO Страницы: 4
Mopar 77072498AB Manual preview
77072498AB
Бренд: Mopar Страницы: 18
Aston Martin V8 Vantage Workshop Manual preview
V8 Vantage
Бренд: Aston Martin Страницы: 415
Rhino-Rack S400-FK2 Instructions preview
S400-FK2
Бренд: Rhino-Rack Страницы: 2
Xforce PR-104 User Manual preview
PR-104
Бренд: Xforce Страницы: 11
Flash Cover MN012 Installation Manual preview
MN012
Бренд: Flash Cover Страницы: 2
SuperATV IN-WS-K-TRX Installation Instructions preview
IN-WS-K-TRX
Бренд: SuperATV Страницы: 2
Audi S4 Biturbo Buyer'S Manual preview
S4 Biturbo
Бренд: Audi Страницы: 9

Бренды по названию

Популярные бренды

Загрузить еще бренды