Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 526 | Manualshive

Страница: 526 / 2589

background image

Fig. 13: Identifying Brake Fluid Level Sensor Connector, Brake Pipe, Master Cylinder Component,

Reverse Tank, O-Ring & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

BRAKE FLUID LEVEL SENSOR INSPECTION

1. Disconnect the brake fluid level sensor connector from the master cylinder.
2. Inspect for continuity according to fluid level between the brake fluid level sensor terminals.

z

If not as indicated in the table, replace the No.1 reserve tank. (See

MASTER CYLINDER

REMOVAL/INSTALLATION

.)

Fig. 14: Connector Terminal Reference

Courtesy of MAZDA MOTORS CORP.

Fig. 15: Identifying Brake Fluid Level Sensor Connector Terminal

Courtesy of MAZDA MOTORS CORP.

POWER BRAKE UNIT INSPECTION

WITHOUT USING SST

Operation inspection

NOTE:

z

The following inspection methods are simple inspection methods to judge

the function of the power brake unit.

z

If there is any malfunction in the power brake unit, replace the power brake
unit as a single unit.

2008 Mazda CX-9 Grand Touring

2008 BRAKES Conventional Brake System - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:48:49 AM

Page 11

© 2005 Mitchell Repair Information Company, LLC.

«
...
524
525
526
527
528
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: Baja Designs Страницы: 6

Бренд: Daihatsu Страницы: 43

Бренд: Pivot Страницы: 4

Бренд: Kia Страницы: 385

Бренд: Carcomm Страницы: 2

Бренд: Whispbar Страницы: 14

Бренд: Whispbar Страницы: 85

Бренд: Cadillac Страницы: 368

Бренд: Luverne Страницы: 3

Бренд: Navman Страницы: 27

Бренд: Draw tite Страницы: 4

Бренд: Mercedes-Benz Страницы: 329

XEBRA ZAPCAR Series

Бренд: Zap Страницы: 16

2005 JR41 Stratus

Бренд: Dodge Страницы: 293

Бренд: Carcomm Страницы: 2

Бренд: Yakima Страницы: 15

Бренд: Mobileye Страницы: 29

Бренд: CITROEN Страницы: 394

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды