Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1725

Страница: 1725 / 2589

Rear
temperature

control volume

Rear climate
control unit

Moving towards
COLD

less

continuity, short circuit
(Front climate control

unit-rear airflow mode
actuator: 3G-C)

Rear climate control
unit

Front climate control

unit: terminal voltage
(2B)

Temperature control
dial (rear side):

Moving towards
medium

temperature

Approx.

2.5

Temperature control
dial (rear side):

Moving towards
HOT

Approx.

4.2

+5 V

Rear climate
control unit

Under any
condition

5.0

Wiring harness:

continuity (Front
climate control unit-

ground: 3H-ground)

Ground

Rear climate

control unit

Under any
condition: Inspect

for continuity to
ground

1.0 or

less

Wiring harness:

continuity (Front
climate control unit-

rear climate control
unit: 31-E)

Panel light

control input

Instrument cluster

Turn the headlight
switch to the off

position

1.0 or

less

Wiring harness:

continuity, short circuit
(Front climate control

unit-instrument cluster:
3J-1I)

TNS relay

Headlight switch

Turn the headlight

switch to the TNS
position

B+

2008 Mazda CX-9 Grand Touring

2008 HVAC Control System (HVAC) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:12:36 AM

Page 46

«
...
1723
1724
1725
1726
1727
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды