Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 724

Страница: 724 / 2589

1. Select "DataLogger".
2. Select "Modules".
3. Select "ABS".

When using the PDS (Pocket PC)

1. Select "Module Tests".
2. Select "ABS".
3. Select "DataLogger".

Fig. 35: Connecting M-MDS To DLC-2

Courtesy of MAZDA MOTORS CORP.

8. Select the "MCYLIP" PID.
9. Start the engine.

10. Depress the brake pedal, and confirm that the fluid pressure value of the SST (Gauge) and the value

shown on the M-MDS are equal

If the fluid pressures are different, replace the DSC/RSC HU/CM. (See

DSC/RSC HU/CM

REMOVAL/INSTALLATION

11. After the inspection, remove the SSTs, install the brake hose, clamp, and brake pipe to the original

positions, and then bleed the air from the brake line.

2008 Mazda CX-9 Grand Touring

2008 BRAKES Dynamic Stability Control/Roll Stability Control - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:40:24 AM

Page 31

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды