Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2408

Страница: 2408 / 2589

Fig. 39: Identifying Sealant Applying Area & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

6. Rain sensor (Vehicles with auto light/wiper system)(See

RAIN SENSOR

REMOVAL/INSTALLATION

)

7. Cowl grille (See

COWL GRILLE REMOVAL/INSTALLATION

8. Windshield wiper arm and blade (See

WINDSHIELD WIPER ARM AND BLADE

REMOVAL/INSTALLATION

17. Allow the sealant to harden completely.

Sealant hardening time: 24 h

REAR WINDOW GLASS REMOVAL

1. Disconnect the negative battery cable.
2. Remove the rear wiper arm and blade. (See

REAR WIPER ARM AND BLADE

REMOVAL/INSTALLATION

3. Remove the liftgate upper trim. (See

LIFTGATE UPPER TRIM REMOVAL/INSTALLATION

4. Remove the liftgate side trim. (See

LIFTGATE SIDE TRIM REMOVAL/INSTALLATION

)

5. Remove the liftgate lower trim. (See

LIFTGATE LOWER TRIM REMOVAL/INSTALLATION

6. Remove the rear wiper motor. (See

REAR WIPER MOTOR REMOVAL/INSTALLATION

7. Remove the rear spoiler. (See

REAR SPOILER REMOVAL/INSTALLATION

8. Remove the high-mount brake light. (See

HIGH-MOUNT BRAKE LIGHT

REMOVAL/INSTALLATION

9. Disconnect the filament connector.

10. Apply protective tape along the edge of the body.

NOTE:

Overlap and adhere the protective tape to the corners to prevent

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Glass/Windows/Mirrors - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:36:16 AM

Page 29

«
...
2406
2407
2408
2409
2410
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды