Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1880

Страница: 1880 / 2589

Fig. 20: Identifying Glove Compartment With Hook

Courtesy of MAZDA MOTORS CORP.

VENTILATOR GRILLE REMOVAL/INSTALLATION

DRIVER SIDE

1. Disconnect the negative battery cable.
2. Remove the following parts:

1. Decoration panel (See

DECORATION PANEL REMOVAL/INSTALLATION

2. Front console box mat (See

FRONT CONSOLE BOX MAT REMOVAL/INSTALLATION

3. Indicator panel (See

INDICATOR PANEL REMOVAL/INSTALLATION

4. Front console box (See

FRONT CONSOLE BOX REMOVAL/INSTALLATION

5. Center panel (See

CENTER PANEL REMOVAL/INSTALLATION

6. Upper column cover (See

COLUMN COVER REMOVAL/INSTALLATION

3. Remove the screws.
4. Remove the hook.
5. Remove the ventilator grille in the direction of the arrow.
6. Install in the reverse order of removal.

Fig. 21: Identifying Ventilator Grille With Hook & Screw - Driver Side

Courtesy of MAZDA MOTORS CORP.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Interior Trim - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:43:26 AM

Page 16

«
...
1878
1879
1880
1881
1882
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды