Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 717

Страница: 717 / 2589

3. Select "DataLogger".

Fig. 24: Connecting M-MDS To DLC-2

Courtesy of MAZDA MOTORS CORP.

4. Select the following PIDs using the M-MDS:

WSPD_LR

(LR ABS wheel-speed sensor)

WSPD_RR

(RR ABS wheel-speed sensor)

5. Start the engine and drive the vehicle.
6. Verify that the display of the M-MDS shows the same value as the speedometer.

If there is any malfunction, replace the rear ABS wheel-speed sensor.

COMBINED SENSOR REMOVAL/INSTALLATION

1. Remove the second-row seat (RH). (See

SECOND-ROW SEAT REMOVAL/INSTALLATION

2. Remove the edge cover. (See

LONG SLIDER REMOVAL/INSTALLATION

WARNING:

If the DSC/RSC sensor initialization procedure is not completed, it

could result in an unexpected accident due to the DSC/RSC being
inoperative. Therefore, after the combined sensor is replaced,

always perform the DSC/RSC sensor initialization procedure to

ensure proper DSC/RSC operation.

CAUTION:

The internal parts of the combined sensor could be damaged if
dropped. Be careful not to drop the combined sensor. Replace the

combined sensor if it is subjected to an impact. Also, do not use an
impact wrench or other similar air tools when removing/installing the

sensor.

2008 Mazda CX-9 Grand Touring

2008 BRAKES Dynamic Stability Control/Roll Stability Control - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:40:24 AM

Page 24

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды