Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2221

Страница: 2221 / 2589

Fig. 2: Identifying Rear Suspension Components Location - AWD

Courtesy of MAZDA MOTORS CORP.

REAR SHOCK ABSORBER REMOVAL/INSTALLATION

1. Remove the trunk side trim. (See

TRUNK SIDE TRIM REMOVAL/INSTALLATION

2. Support the rear lower arm using a garage jack.
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.

2008 Mazda CX-9 Grand Touring

2008 SUSPENSION Rear Suspension - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:24:01 AM

Page 2

«
...
2219
2220
2221
2222
2223
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды