Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 346

Страница: 346 / 2589

9. Measure the resistance between the coupler component terminals B7 and B8.

If there is any malfunction, replace the TFT sensor. (See

TRANSAXLE FLUID

TEMPERATURE (TFT) SENSOR REMOVAL/INSTALLATION [AW6A-EL, AW6AX-

EL]

Transaxle fluid temperature (TFT) sensor

RESISTANCE REFERENCE

10. Install the TFT sensor. (See

TRANSAXLE FLUID TEMPERATURE (TFT) SENSOR

REMOVAL/INSTALLATION [AW6A-EL, AW6AX-EL]

11. Install the control valve body. (See

CONTROL VALVE BODY REMOVAL/INSTALLATION

[AW6A-EL, AW6AX-EL]

Fig. 13: Measuring Resistance Between Coupler Component Terminals B7 & B8

Courtesy of MAZDA MOTORS CORP.

12. Install the oil pipe. (See

OIL COOLER REMOVAL/INSTALLATION [AW6A-EL, AW6AX-EL]

13. Install the oil cooler. (See

OIL COOLER REMOVAL/INSTALLATION [AW6A-EL, AW6AX-EL]

14. Add ATF to the specified level. (See

AUTOMATIC TRANSAXLE FLUID (ATF) REPLACEMENT

[AW6A-EL, AW6AX-EL]

15. Install the air cleaner component. (See

INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [MZI-

3.7]

16. Connect the negative battery cable.

TRANSAXLE FLUID TEMPERATURE (TFT) SENSOR

ATF temperature (°C {°F}) Resistance (kilohm)

10 {50}

5.62-7.31

25 {77}

Approx. 3.5

110 {230}

0.22-0.27

2008 Mazda CX-9 Grand Touring

2008 TRANSMISSION Automatic Transaxle (AW6A-EL, AW6AX-EL) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:29:30 AM

Page 18

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды