Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1553 | Manualshive

Страница: 1553 / 2589

background image

1. Detach the T-stud which secure sections A of roof molding, using a flat head screwdriver or equivalent

tool.

2. While pulling the roof molding up, detach it from the clips at section B, C, and then remove the roof

molding.

Fig. 9: Identifying Roof Molding With T-Stud And Clips

Courtesy of MAZDA MOTORS CORP.

ROOF MOLDING INSTALLATION

1. Attach the roof molding to the T-stud at the front portion of section A.
2. Hook the roof molding to clips B, C and press it in to attach.
3. Attach the roof molding to the T-stud at the rear portion of section A.

2008 Mazda CX-9 Grand Touring

2008 ACCESSORIES & BODY, CAB Exterior Trim - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:44:03 AM

Page 8

© 2005 Mitchell Repair Information Company, LLC.

«
...
1551
1552
1553
1554
1555
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

FRONT HEADLIGHT LENS COVER

Бренд: Bimmer Jakes Страницы: 4

Бренд: Chevrolet Страницы: 494

Бренд: Axxess Страницы: 4

Бренд: Vintage Air Страницы: 14

Бренд: Whispbar Страницы: 15

Бренд: muth Страницы: 10

Tata Indigo Diesel

Бренд: TATA Motors Страницы: 190

Prime Design HBR-E-FT33B

Бренд: Safe Fleet Страницы: 12

Alloy Rugged Ridge X-Clamp

Бренд: Omix-Ada Страницы: 2

Бренд: Dodge Страницы: 3

Бренд: Atera Страницы: 3

Бренд: Black Horse Страницы: 5

Бренд: ConWys AG Страницы: 16

1995 Cutlass Supreme

Бренд: Oldsmobile Страницы: 340

Бренд: Mitsubishi Страницы: 490

Бренд: Edelbrock Страницы: 2

Бренд: Valueline Страницы: 40

Бренд: Volvo Страницы: 304

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды