Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2084

Страница: 2084 / 2589

SYSTEM]

TROUBLESHOOTING CHART

DIAGNOSTIC PROCEDURE

Display screen changes to black.

POSSIBLE

CAUSE

Open or short circuit in car-navigation unit (power supply (B+)) wiring
harness

Open or short circuit in car-navigation unit (power supply (ACC)) wiring

harness

Open or short circuit in car-navigation unit (GND) wiring harness

Open or short circuit in wiring harness between audio unit and car-navigation
unit

Poor connection of rear mount camera control module connector, terminal

damage

Open or short circuit in audio unit (power supply (B+)) wiring harness

Open or short circuit in audio unit (power supply (ACC)) wiring harness

Open or short circuit in audio unit (power supply (IG1)) wiring harness

Open or short circuit in audio unit (GND) wiring harness

Open or short circuit in wiring harness between audio unit and rear view

monitor

Poor connection of car-navigation unit connector, terminal damage

Poor connection of audio unit connector, terminal damage

Car-navigation unit malfunction

Audio unit malfunction

STEP

INSPECTION

ACTION

Turn the ignition switch to the

ACC position.

Does the display screen change

from blank to NAVI mode when
pressing the joystick of the car-

navigation control switch?

Yes

The system is normal.

NOTE:

If the "VOICE" button is pressed for

approx.

2 s or more

, the "DISP OFF" menu appears

on the bottom-left side of screen. If "DISP
OFF" mode is selected, the audio unit will

not display anything. "DISP OFF" mode is
cancelled when the ignition switch is turned

to the LOCK position or the joystick of the
car-navigation control switch is pressed.

Go to the next step.

Shift the selector lever in R
position.

Yes Go to the next step.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Symptom Troubleshooting (Car Navigation System) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:40:43 AM

Page 3

«
...
2082
2083
2084
2085
2086
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды