Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1893 | Manualshive

Страница: 1893 / 2589

background image

Fig. 43: Identifying Grommet & Clip

Courtesy of MAZDA MOTORS CORP.

6. Insert a tape-wrapped flathead screwdriver between the body and the grommet.
7. Press the tabs and remove the grommet.
8. Install the new grommet to the body.
9. Install the new clip B to the A-pillar trim.

10. Install the A-pillar trim.

Fig. 44: Inserting Screwdriver Between Body & Grommet

Courtesy of MAZDA MOTORS CORP.

FRONT SIDE TRIM REMOVAL/INSTALLATION

1. Remove the front scuff plate inner. (See

FRONT SCUFF PLATE REMOVAL/INSTALLATION

.)

2. Partially peel back the seaming welt.
3. Remove the nut.
4. Pull the front side trim upward, then detach clip A, pin B.
5. Remove the front side trim.
6. Install in the reverse order of removal.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Interior Trim - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:43:26 AM

Page 29

© 2005 Mitchell Repair Information Company, LLC.

«
...
1891
1892
1893
1894
1895
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: DANA Страницы: 42

Бренд: dallara Страницы: 37

Бренд: Yakima Страницы: 8

Бренд: Federal Signal Corporation Страницы: 8

Бренд: Federal Signal Corporation Страницы: 8

Бренд: Jeep Страницы: 608

Бренд: Mazda Страницы: 720

Бренд: Chariot Carriers Страницы: 3

Бренд: CITROËN Страницы: 301

Polaris TATOU 4S

Бренд: Camoplast Страницы: 13

Бренд: Mitsubishi MOTORS Страницы: 416

Giulietta 2.0 JTDM

Бренд: Alfa Romeo Страницы: 14

84 61 0 028 926

Бренд: BMW Страницы: 13

Бренд: Roadtrek Страницы: 61

Бренд: Buick Страницы: 161

Civic Hatch 2017

Бренд: Honda Страницы: 687

Aura Mobile BT MCP-2014

Бренд: Spracht Страницы: 2

Бренд: Yakima Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды