Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 251

Страница: 251 / 2589

Fig. 169: Identifying Rear Planetary Gear Component And One-Way Clutch Component Assembly

Courtesy of MAZDA MOTORS CORP.

Assembly Procedure

1. Apply grease to the thrust washer.
2. Install the thrust washer to the rear planetary gear component.

CAUTION:

Apply grease to the mounting surface of the thrust washer so that it

will not drop when the rear planetary gear component is installed.

Do not apply grease to the oil holes of the thrust washer.

CAUTION:

Apply grease to the mounting surface of the thrust washer so

that it will not drop when the rear planetary gear component is
installed.

2008 Mazda CX-9 Grand Touring

2005-08 TRANSMISSION Automatic Transaxle Overhaul (AW6A-EL) - CX-7, CX-9 & Mazda 6

Microsoft

Sunday, November 15, 2009 10:28:16 AM

Page 88

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды