Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1835

Страница: 1835 / 2589

CHECK CODE INSPECTION

Check code 01

CHECK CODE INSPECTION CHART (CHECK CODE 01)

Check code 02

CHECK CODE INSPECTION CHART (CHECK CODE 02)

Courtesy of MAZDA MOTORS CORP.

Check code 01 CAN system

INSPECTION

CONDITION

DISPLAY

ACTION

Select the check
code 01.

CAN system of information display is normal.

CAN system communication error. (DTC

U2516) (See

DTC TABLE [MULTIPLEX

COMMUNICATION SYSTEM]

)

Check code 02

Communication status to audio unit

Communication status to climate control unit

INSPECTION

CONDITION

DISPLAY

ACTION

All communications are

normal.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Instrumentation/Driver Info - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:42:27 AM

Page 25

«
...
1833
1834
1835
1836
1837
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды