Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2379

Страница: 2379 / 2589

NO.8 PASSENGER DOOR GLASS OPERATES ACCIDENTALLY [POWER

WINDOW SYSTEMS (EXTERIOR OPEN/CLOSE FUNCTION)]

POSSIBLE CAUSE CHART

DIAGNOSTIC PROCEDURE

keyless control module

Go to the next step.

Inspect if malfunction is in
operating power window main

switch

Yes

Inspect power window main switch

(See

POWER WINDOW MAIN SWITCH

INSPECTION

Go to the next step.

Inspect if malfunction is in

without operating Step 1 to 3

Yes

Inspect the following parts and repair or replace

Power window subswitch (passenger side)

(See

POWER WINDOW SUBSWITCH

INSPECTION

BCM (See

BODY CONTROL MODULE

(BCM) INSPECTION

Wiring harness between power window

subswitch (passenger side) and power window
main switch

Reinspect for malfunction recurrence. If the

malfunction is not corrected, repeat the procedure from

Step 1.

Passenger door glass operates accidentally

POSSIBLE CAUSE

Power window subswitch (passenger side) malfunction

ACTION

Inspect the power window subswitch of the passenger door glass and repair or replace
(See

POWER WINDOW SUBSWITCH INSPECTION

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Symptom Troubleshooting [Power Window System (Exterior Open/Close Function)] -

Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:37:40 AM

Page 11

«
...
2377
2378
2379
2380
2381
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды