Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2206

Страница: 2206 / 2589

2008 DRIVELINE/AXLE

Propeller Shaft - Mazda CX-9

PROPELLER SHAFT LOCATION INDEX

Fig. 1: Identifying Propeller Shaft

Courtesy of MAZDA MOTORS CORP.

PROPELLER SHAFT ON-VEHICLE INSPECTION

JOINT AREA EXCESSIVE PLAY INSPECTION

1. Shake the universal joint by hand and verify that there is no excessive play.
2. If there is any excessive play, replace the propeller shaft. (See

PROPELLER SHAFT

REMOVAL/INSTALLATION

2008 Mazda CX-9 Grand Touring

2008 DRIVELINE/AXLE Propeller Shaft - Mazda CX-9

2008 Mazda CX-9 Grand Touring

2008 DRIVELINE/AXLE Propeller Shaft - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:53:04 AM

Page 1

Microsoft

Sunday, November 15, 2009 9:53:10 AM

Page 1

«
...
2204
2205
2206
2207
2208
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды