Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1421

Страница: 1421 / 2589

1. Remove the engine cover in the order indicated in the figure.

2. Install in the reverse order of removal.

Fig. 12: View Of Engine Cover Side

Courtesy of MAZDA MOTORS CORP.

VALVE CLEARANCE INSPECTION/ADJUSTMENT [MZI-3.7]

VALVE CLEARANCE INSPECTION

1. Disconnect the negative battery cable.
2. Remove the engine cover. (See

ENGINE COVER REMOVAL/INSTALLATION [MZI-3.7]

3. Remove the ventilation hose.
4. Remove the resonance chamber. (See

INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [MZI-

3.7]

5. Remove the dynamic chamber and throttle body as a single unit. (See

INTAKE-AIR SYSTEM

REMOVAL/INSTALLATION [MZI-3.7]

6. Disconnect the wiring harness.
7. Remove the ignition coils. (See

IGNITION COIL REMOVAL/INSTALLATION [MZI-3.7]

8. Remove the dipstick.
9. Remove the cylinder head cover. (See

TIMING CHAIN REMOVAL/INSTALLATION [MZI-3.7]

NOTE:

Firmly pull the engine cover near the locations shown to disengage

the retainers.

2008 Mazda CX-9 Grand Touring

2008 ENGINE Mechanical (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:01:57 AM

Page 11

«
...
1419
1420
1421
1422
1423
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды