Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2151

Страница: 2151 / 2589

DTC B2700 [POWER LIFTGATE (PLG) SYSTEM]

DTC B2700 - DETECTION CONDITION POSSIBLE CAUSE CHART

touch sensor (LH) terminal A for an open
circuit/short circuit to power supply

system.

Is the wiring harness normal?

Repair or replace the wiring harness.

Go to the next step.

VERIFY CORRECTION COMPLETED

Reconnect the disconnected connector.

Clear the DTC.

Is DTC B2669 stored after

1 min or more

have elapsed?

Yes

Replace the PLG control module.

(See

POWER LIFTGATE (PLG) DRIVE

UNIT REMOVAL/INSTALLATION

DTC troubleshooting completed.

DTC B2700

PLG touch sensor (RH) circuit malfunction

DETECTION

CONDITION

Open circuit is detected in the PLG touch sensor (RH)

POSSIBLE CAUSE

Short to power supply circuit in wiring harness between PLG control module
terminal 3A and PLG touch sensor (RH) terminal B

Open circuit in wiring harness between PLG control module terminal 3A and

PLG touch sensor (RH) terminal B

Short to power supply circuit in wiring harness between PLG control module
terminal 2D and PLG touch sensor (RH) terminal A

Open circuit in wiring harness between PLG control module terminal 2D and

PLG touch sensor (RH)terminal A

PLG touch sensor malfunction

PLG control module malfunction

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES On-Board Diagnostic (Power Liftgate (PLG) System) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:46:08 AM

Page 30

«
...
2149
2150
2151
2152
2153
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды