Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1909 | Manualshive

Страница: 1909 / 2589

background image

Fig. 72: Identifying Seat Side Box With Clips & Tab

Courtesy of MAZDA MOTORS CORP.

LIFTGATE UPPER TRIM REMOVAL/INSTALLATION

1. Detach tabs A, clips B, and pin C by pulling them in the direction of the arrow.
2. Remove the liftgate upper trim.
3. Install in the reverse order of removal.

Fig. 73: Identifying Liftgate Upper Trim, Clips, Pin & Tab

Courtesy of MAZDA MOTORS CORP.

LIFTGATE SIDE TRIM REMOVAL/INSTALLATION

1. Remove the liftgate upper trim. (See

LIFTGATE UPPER TRIM REMOVAL/INSTALLATION

.)

2. Remove the PLG arm band. (Vehicles with PLG)
3. Remove the fastener.
4. Detach clips A and tab C by pulling them in the direction of the arrow.
5. Remove the liftgate side trim.
6. Install in the reverse order of removal.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Interior Trim - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:43:26 AM

Page 45

© 2005 Mitchell Repair Information Company, LLC.

«
...
1907
1908
1909
1910
1911
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: iDataLink Страницы: 106

Бренд: GMC Страницы: 120

Бренд: Prime Tech Страницы: 6

Бренд: Fiat Страницы: 24

Бренд: Valeo Страницы: 28

Бренд: Simplicity Страницы: 10

Бренд: GMC Страницы: 430

Бренд: ULTIMATE SPEED Страницы: 40

Jumpy Miltispace

Бренд: CITROËN Страницы: 164

Бренд: Directed Страницы: 30

Бренд: Phonocar Страницы: 28

Бренд: Whispbar Страницы: 34

BEDXTENDER HD 74805-00A

Бренд: AMP Research Страницы: 7

Бренд: AA Products Страницы: 6

Бренд: Bushranger Страницы: 5

Бренд: ZUS Страницы: 15

Бренд: Tessera4x4 Страницы: 16

Бренд: PCCM Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды