Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1256

Страница: 1256 / 2589

DTC P2127 [MZI-3.7]

DTC P2127 (MZI-3.7) DETECTION CONDITIONS AND POSSIBLE CAUSES

Start the engine.

Is the same DTC present?

Go to the next step.

VERIFY AFTER REPAIR
PROCEDURE

Perform the "AFTER REPAIR

PROCEDURE". (See

AFTER

REPAIR PROCEDURE [MZI-

3.7]

Are any DTC present?

Yes

Go to the applicable DTC inspection. (See

DTC

TABLE [MZI-3.7]

DTC troubleshooting completed.

DTC P2127

APP sensor No.2 circuit low input

DETECTION

CONDITION

APP sensor No.2 is out of self-test range low.

POSSIBLE CAUSE

Short to ground circuit between APP sensor terminal F and PCM terminal
1BA

Short to ground circuit between APP sensor terminal D and PCM terminal

Short to ground circuit between APP sensor terminal G and PCM terminal
1AD

Short to ground circuit between APP sensor terminal C and PCM terminal

1AH

Short to ground circuit between APP sensor terminal H and PCM terminal 1

Connector or terminal malfunction

APP sensor malfunction

2008 Mazda CX-9 Grand Touring

2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:08:43 AM

Page 392

«
...
1254
1255
1256
1257
1258
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды