Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 557

Страница: 557 / 2589

Fig. 5: Identifying Generator, Generator Connector, Lower Bolt & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

GENERATOR LOWER BOLT REMOVAL NOTE

1. Fully loosen the generator lower bolt.

NOTE:

The generator lower bolt cannot be fully removed from the engine because

it contacts the body frame. However, the generator can be
removed/installed without fully removing the lower bolt because there is a

notch at the lower bolt installation part of the generator.

2008 Mazda CX-9 Grand Touring

2008 ENGINE Charging System (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:54:57 AM

Page 7

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды