Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2425

Страница: 2425 / 2589

Fig. 66: View Of Outer Mirror Garnish

Courtesy of MAZDA MOTORS CORP.

OUTER MIRROR GARNISH INSTALLATION

1. Position the outer mirror garnish against the mirror body in the direction of the arrow shown in the figure,

and insert the outer mirror garnish clips (6 locations) into the mirror body.

2. Install the outer mirror garnish so that there are no gaps around the component.

Fig. 67: View Of Outer Mirror Garnish

Courtesy of MAZDA MOTORS CORP.

POWER OUTER MIRROR INSPECTION

1. Apply battery positive voltage to the power outer mirror terminals and inspect the operation of the power

outer mirror.

If not as specified, replace the power outer mirror.

MIRROR OPERATION CHART

Mirror operation

terminal
B+ GND

Down

Left

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Glass/Windows/Mirrors - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:36:17 AM

Page 46

«
...
2423
2424
2425
2426
2427
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды