Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1935

Страница: 1935 / 2589

Fig. 28: Identifying Inboard Light Bulb, Taillight Bulb, Connector & Socket

Courtesy of MAZDA MOTORS CORP.

4. Install in the reverse order of removal.

LICENSE PLATE LIGHT REMOVAL/INSTALLATION

LICENSE PLATE LIGHT

1. Disconnect the negative battery cable.
2. Remove the liftgate upper trim.(See

LIFTGATE UPPER TRIM REMOVAL/INSTALLATION

3. Remove the liftgate side trim.(See

LIFTGATE SIDE TRIM REMOVAL/INSTALLATION

4. Remove the liftgate lower trim.(See

LIFTGATE LOWER TRIM REMOVAL/INSTALLATION

5. Remove in the order indicated in the table.

Fig. 29: Identifying License Plate Light, Connector & Lens

Courtesy of MAZDA MOTORS CORP.

6. Install in the reverse order of removal.

LICENSE PLATE LIGHT BULB

1. Disconnect the negative battery cable.
2. Remove in the order indicated in the table.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Lighting Systems - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:39:06 AM

Page 19

«
...
1933
1934
1935
1936
1937
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды