Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 16

Страница: 16 / 2589

DTC B1013

DTC B1013 DETECTION CONDITION AND POSSIBLE CAUSE

curtain air bag
module resistance)

1.0-9.7 ohms

2AL

RES_PT_D
(Driver-side pre-

tensioner seat belt
resistance)

ohm

Under any condition:

1.0-9.7 ohms

2N, 2J

RES_PT_P

(Passenger-side
pre-tensioner seat

belt resistance)

ohm

Under any condition:
1.0-9.7 ohms

2A, 2E

RES_SAB_D

(Driver-side side
air bag module

resistance)

ohm

Under any condition:
1.0-9.7 ohms

2B, 2F

RES_SAB_P
Passenger-side side

air bag module
resistance)

ohm

Under any condition:

1.0-9.7 ohms

21, 2M

TRAK_SW Seat
track position

sensor state)

Forward/Rearward

Front seat front

position: Forward

Front seat rear
position:

Rearward

2AB,

2AF

(1)

Used during seat weight sensor calibration setting. Not necessary for diagnostic.

(2)

When the calibration error is displayed, the error can be cleared by turning the ignition switch to the

LOCK position.

DTC B1013

Seat weight sensor calibration error

DETECTION

CONDITION

Calibration set value not within valid range.

WARNING:

Detection conditions are for understanding the DTC outline before

performing an inspection. Performing an inspection according to only the
detection conditions may cause injury due to an operating error, or damage

the system. When performing an inspection, always follow the inspection
procedure.

POSSIBLE

Weight acting on front passenger-side seat during calibration

Improperly installed front passenger-side seat part at time of calibration

Deformed floor where attached to front passenger-side seat

Deformed front passenger-side seat under-bracket or frame

2008 Mazda CX-9 Grand Touring

2008 RESTRAINTS On-Board Diagnostic (Restraints) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:18:46 AM

Page 16

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды